Which Nanit Mount Should You Choose: Floor, Wall, or Flex?
For most nurseries, a floor stand is the easiest nanit baby monitor stand to place for a crib view. Choose wall mounting if you want a fixed high angle and cannot give up floor space. Choose the Flex stand if you need to move the camera often between rooms.
On this page (12 sections)
- How does a floor stand compare for crib placement?
- How does a wall mount compare for a fixed view?
- How does the Flex stand compare for portability?
- Which mount gives the best crib view for a newborn?
- Which nanit baby monitor stand height works as your baby grows?
- How stable does a floor stand need to be?
- Which option suits renters and small rooms?
- How do you set up each mount without tools?
- When does a non-Nanit monitor make more sense?
- How do you choose between Nanit and Owlet for mount needs?
- How do you care for a stand and keep the view clear?
- Which mount should you buy for your nursery?
For most nurseries, a floor stand is the easiest nanit baby monitor stand to place for a crib view. It stands over the crib, needs no holes, and moves when the room changes.
A wall mount gives the most fixed view from above. A Flex stand gives the most freedom to lift the camera and place it on furniture or move it for travel.
This guide compares those three choices by view, height, portability and reach. We checked the specs for the stands and cameras named here.
We did not test them in a nursery.
How does a floor stand compare for crib placement?
A floor stand suits most families because you can position it in minutes and move it later. You do not need tools or wall damage.
You can push it closer or farther as the crib grows.
The main trade-off is floor space. A heavy round base takes a footprint beside the crib.
Keep it out of the path where you walk at night.
View quality depends on height and angle. A stand near 69 inches can look down into a crib.
A lower stand, near 37 inches, suits a bassinet or a playard where a high angle would be too steep.
Stability matters more than it sounds. A gooseneck arm can bend, so set the curve once and leave it.
A solid iron base helps the stand stay put when you bump it.

A floor stand with adjustable height from 37.4 to 68.8 inches, a gooseneck arm and a heavy base for a Nanit Pro camera.
See it on AmazonDidalo says this stand fits the Nanit Pro, plus the Nanit Plus and the original Nanit camera. The camera itself is not included.
That point matters if you plan to move your own camera onto the stand.
Rule: pick a floor stand if you want the fastest set-up and a view you can change. Pick it for rentals, shared rooms and rooms where furniture moves.
How does a wall mount compare for a fixed view?
A wall mount suits a nursery where the crib will stay in one place for months. It keeps the floor clear and holds the camera at a set height.
The view is fixed by your screws. Measure twice before you drill, as a small error can leave one end of the crib out of frame.
It also keeps the camera out of reach as your baby starts to pull up and cruise. A floor stand can tip or shift if a toddler grabs a pole.
You gain no portability, as the mount stays on the wall when you travel or move. You would need a second mount or a different stand for another room.
Keep the cable away from the crib and from a path where it can be pulled. A wall outlet near the mount gives the cleanest run.
For the camera itself, see our nanit pro baby monitor review for setup and app details. The mount does not change camera features, but it changes what the camera can see.
Rule: pick a wall mount if the crib spot is final and floor space is tight. Skip it if you rent and cannot patch holes, or if you move the crib often.
How does the Flex stand compare for portability?
The Flex stand suits parents who move the camera between rooms or take it on trips. It bends and clamps in ways a floor stand cannot.
Flex arms work best on a sturdy rail, shelf edge or piece of furniture. They give a close view in a small space.
They are less steady than a heavy floor base.
Bending the arm changes the angle each time you move it. That is a plus for a bassinet one week and a travel crib the next.
It is a minus if you want the same framing every night.
Cord control is part of the job. A Flex arm holds the camera, but the power cable still needs a safe path.
Keep it taped or routed away from the sleep space.
Portability also affects your whole monitor plan. If you need a set-up for a second home, read can you use a Nanit baby monitor for travel? before you pack a mount.
Rule: pick a Flex stand if moving the camera matters more than a fixed frame. It fits travel, co-sleeping rooms and small spaces where a floor base will not fit.
Which mount gives the best crib view for a newborn?
For a newborn, a higher camera angle usually shows more of the crib and the sleep area. It also shows whether a blanket or limb is out of place.
Newborns stay in one spot, so a steep downward view works well. You can see the full mattress without panning.
A lower angle may show mostly the rail.
Sound and motion alerts do not depend on the mount. Framing does.
If the camera misses the crib corner, the app cannot fix that.
Light in the room matters too. A high stand can catch a window or a night light in the frame.
Test the view at night before you settle the stand.
A bassinet needs a lower view than a full crib. The same stand set at 69 inches may be too high for a bedside sleeper.
Lower it or move it back until the whole bassinet fits in frame.
Rule: set the mount so the whole sleep surface fills the frame, with a little floor around it. If you see mostly rail, raise the stand or move it back.
Which nanit baby monitor stand height works as your baby grows?
Height is the setting you will change most as your baby grows. Start higher for a newborn and lower it as your baby sits, stands and moves around the crib.
A stand that adjusts from 37.4 to 68.8 inches covers a bassinet and a crib. That range lets one stand serve two sleep spaces in the first year.
Lowering the stand also reduces the chance of a bump. A tall pole beside a crib can wobble if you catch it in the dark.
A shorter pole is harder to knock.
Check the view after each change. A camera that framed a newborn well may cut off a toddler who stands at the rail.
Move the base back or lower the head until the child and the mattress both fit.
Growth is not the only reason to adjust height. A new crib, a moved dresser or a changed bedside lamp can all shift the best angle.
Rule: buy a stand with a wide height range if your baby will move from a bassinet to a crib. It saves you from buying a second mount at six months.
What does adjustable height mean in daily use?
Adjustable height means you can match the stand to the sleep space without a new purchase. A telescoping pole or extension tubes let you set the camera over a low bassinet or a tall crib.
Look for clear stops or marks so you can return to the same height. That helps if you move the stand for cleaning and set it back the same night.
Height also changes stability. A stand at full height wobbles more than the same stand at half height.
Set the base on a hard floor or a flat rug, not on a thick pile.
Rule: pick a stand you can adjust with one hand and lock without tools. If it needs a lecture each time, you will leave it at one height and lose the benefit.
How stable does a floor stand need to be?
A nanit baby monitor stand needs a base heavy enough that a bump does not move the camera. The view must stay the same through the night.
Didalo uses a solid iron base and metal poles. That design aims to fix looseness that buyers often mention with lighter mounts.
A heavy base also resists a pet or a toddler who brushes past it.
Gooseneck arms add flex. Flex helps you aim the camera, but it can also drift.
Bend the arm, set the camera, then check the frame again after an hour.
Pole joints matter too. Extension tubes should fit snugly.
If the pole twists, the camera angle twists with it.
Place the base where you will not step on it. A stand behind a door or in a walk path will get knocked more than a stand in a quiet corner.
Rule: choose the heaviest base that still fits your floor space. Stability beats extra height you cannot use safely.
How do you keep a stand from tipping or shifting?
Keep the base flat, the pole tight and the stand out of walk paths. Those three steps prevent most bumps.
Tighten each pole joint before you hang the camera. A loose joint at 68 inches acts like a lever.
A snug joint at the same height feels firm.
Route the power cable so it does not pull the stand. A cable caught on a foot can drag the base across the floor.
Tape the cable to the pole or run it along the wall.
Check the floor type. A round base on a thick rug can rock.
Move the stand to a hard section or flatten the rug under the base.
Rule: if the stand moves when you brush it, move it or weight it before the first night. Do not rely on luck in a dark room.
Which option suits renters and small rooms?
Renters and small rooms usually suit a floor stand or a Flex stand, not a wall mount. Both avoid holes and both move when you leave.
A floor stand needs a clear strip of floor beside the crib. Measure that strip before you buy.
A bassinet in a shared room may leave no room for a round base.
A Flex stand needs no floor space. It needs a solid edge to grip.
A dresser, a shelf or a crib rail can work if the clamp fits and the surface is strong.
Wall mounts are the hardest to undo. Even a small hole needs patching and paint.
Some landlords charge for that work at move-out.
Noise at night also matters in small rooms. A stand you bump while half asleep can wake you and your partner.
Place it where your normal path will not hit it.
Rule: if you rent or share a room, start with a floor stand or a Flex stand. Add a wall mount only when the room and the lease both allow it.
How do you set up each mount without tools?
Floor and Flex mounts win on set-up because most need no tools and no wall damage. You snap the camera on, adjust the height and check the frame.
A floor stand usually needs the base, poles and arm joined by hand. Didalo describes snap-on use: move the camera from a Flex stand, wall mount or floor stand and snap it into this stand.
That helps if you already own a Nanit mount.
A Flex stand needs a clamp and a bend. Set it on furniture, bend the arm and aim the camera.
Test the grip before you leave it overnight.
A wall mount needs a drill, anchors and level work. It takes the most time and care, and it leaves the most marks if you change your mind.
After any set-up, check three things in the app. The whole crib should fit in frame, night vision should show the mattress clearly, and the power cable should stay out of the sleep space.
Rule: pick the mount you can set up and check in one sitting. A mount you dread will stay in a box while your baby sleeps without a view.
When does a non-Nanit monitor make more sense?
A non-Nanit monitor makes more sense if you want audio only, no WiFi or a hand-held screen. A Nanit stand will not help if you do not use a Nanit camera.

An audio-only DECT monitor with an 8-hour battery, a belt clip and a 1,000 ft range for parents who want no app.
See it on AmazonVTech says the DM111 uses DECT 6.0 with no static and no WiFi. It has a 5-level sound indicator and a mute function.
It links in under 60 seconds with no account.

A no-WiFi video monitor with a 5-inch screen, 355-degree pan and tilt, night vision and two-way audio.
See it on AmazonHelloBaby says the HB6550 uses 2.4 GHz FHSS with digital encryption and no WiFi. It has a 30-hour battery for the screen unit.
The camera needs a plug.
These options suit grandparents, travel and second rooms. They also suit parents who do not want alerts on a phone.
Our best baby monitor system guide compares those systems in more depth.
If you plan two cameras on one account, read how to choose a nanit dual baby monitor set-up. That choice changes which mounts you need for each room.
Rule: buy a Nanit stand only for a Nanit camera. If you want no WiFi or audio only, buy the monitor that fits that need first.
How do you choose between Nanit and Owlet for mount needs?
Mount needs rarely decide between Nanit and Owlet, but room layout can tip the choice. Both systems need a clear view of the sleep space.
A fixed camera needs a stable mount. A wearable or sock-based system may need less perfect framing.
That difference matters if your nursery has no good wall or floor spot.
App and alert style matter more for most families. Compare video, motion alerts and sound alerts before you compare stands.
Our nanit baby monitor vs owlet guide walks through those system differences. Read it before you commit to a camera and then buy mounts around that camera.
Rule: choose the camera system first, then the mount that fits that camera. Do not buy a stand to fix a system you do not want.
How do you care for a stand and keep the view clear?
Care for a stand by tightening joints, wiping the camera lens and checking the cable weekly. Small checks keep the view steady.
Wipe the lens with a dry, soft cloth. A smudge can look like haze in night vision.
Do not use sprays on the lens.
Dust the poles and base with a damp cloth. Metal poles wipe clean.
Check that the base still sits flat after a move or a deep clean.
Inspect the cable for kinks or pulls. A cable that hangs into the crib is a safety risk.
Route it away from the sleep space and tape it where a child could grab it.
If you use a Flex arm, check the clamp monthly. Clamps can loosen as furniture shifts.
Tighten the grip and test the hold before bedtime.
Rule: do one weekly check of joints, lens and cable. It takes two minutes and it keeps the camera where you left it.
Which mount should you buy for your nursery?
Buy a floor stand if you want a simple crib view you can move, a wall mount if the crib will not move, and a Flex stand if you travel or share a small room. That is the whole choice in one line.
A floor stand fits most first nurseries. It needs no holes, it sets up fast and it adjusts from a bassinet height to a crib height.
Didalo's stand, for example, adjusts from 37.4 to 68.8 inches and fits the Nanit Pro, Plus and original cameras.
A wall mount fits a final nursery layout. It holds a fixed high angle and keeps the floor clear, but it asks for drills, anchors and a spot you will keep for months.
A Flex stand fits a moving life. It clamps to furniture, bends to a new angle and packs for a trip, but it needs a solid edge and a safe cable path.
Whichever mount you pick, frame the whole sleep surface and keep the cable out of reach. Then check the view at night, not just in daylight, as a stand only helps if the camera sees the crib clearly all night.
Our score weighs specs, features and buyer feedback against what you're shopping for. For mounts, that means height range, base stability and fit for your camera model.
Frequently asked questions
Is a floor stand or wall mount better for a Nanit camera?
A floor stand is better if you rent, move furniture or need to change the crib position. A wall mount is better if you want a fixed height and want the floor clear.
Both should give you a full view of the crib without the camera sitting where your baby can reach it.
Can you move a Nanit camera between a Flex stand and a floor stand?
Yes, you can snap the camera from one mount to another if the mounts are made for that camera. Check the exact camera model before you buy.
A mount made for the Nanit Pro may also fit the Nanit Plus and the original Nanit camera.
What height should a Nanit floor stand be?
Set the height so the camera looks down into the crib rather than across it. A stand that adjusts from about 37 to 69 inches lets you match a bassinet, a crib or a playard.
Lower the stand late in infancy so the view stays steady as your baby moves.
Do you need a Nanit stand if you already use a different monitor?
No, a Nanit stand only helps if you use a Nanit camera. If you want audio only or no WiFi, another monitor may suit you better.
Our guide to a best baby monitor system can help you compare that choice.
About this guide: Our look at nanit baby monitor stands compared draws on maker specs, materials and what owners report. See how we research.



